It is vitally important that you keep your bike well maintained. A well maintained bike performs at its best and is a pleasure to ride and also ensures that your components last longer. Below are a few tips to help you or you can always drop in for advice or to have the work carried out in our workshop (see workshop page for prices) Cleaning Cleaning your bike after every ride is not always practical or possible. Assuming regular use, a weekly clean, or after every really mucky ride ensures that dirt and grime never build up. It will take far less time and effort if done regularly. Regardless of what kind of bike you have the principals remain the same. The majority of your efforts should be focused on the drive chain, particularly if you are short on time. Better to do a really spotless job on cleaning just the chain, cassette, chainrings and rear derailleur (jockey wheels) and leave the rest of the bike a bit dirty than to do a quick "half job" on the whole thing. Never re-lubricate the chain whilst it is still dirty. The dirt and grit on the chain will simply combine with lubricant and leave you with a black, filthy mess, which forms an abrasive paste that will wear away at your chain and sprockets at an alarming rate. Having the correct tools for the job will make it much simpler and the job can be done in a fraction of the time. Invest in a good set of brushes. A wide, soft brush can be used for getting rid of the majority of muck from the larger surface areas, a stiffer brush is good for working round rims and tyres and smaller brushes for getting into the gaps between components and your frame. Some brushes are specifically shaped to get into the really hard to reach places, such as the tiny gaps between the sprockets on the cassette. Make sure brushes are good quality and nothing metallic that could scratch your bike. Using a cleaning product to help break down the grime will make this part of the job easier. Several relatively inexpensive products are available in a simple to use trigger spray that are safe to use on all parts of the bike. Cleaning the chain itself can be a major chore unless you invest in a chain cleaner and some degreaser. A chain cleaner is a hand held device that fits onto the chain. By back pedalling, the chain is passed through a small bath of degreaser over a series of stiff brushes that clean the chain on all sides. With a few turns of the pedal the job is done effortlessly and the muck from the chain held within the cleaning device and not flicked all over your frame. Water-soluble degreasers can be rinsed off with plain water to remove any residue. Any degreaser left behind on the chain after cleaning will begin to break down any new oil that is applied. It is strongly recommended that products such as white spirit, petrol or paraffin are not used for chain cleaning. Bike specific cleaning products are there to help protect the components of the bike. The use of car cleaning products like wash and wax can cause loss of performance to mountain bike disc brake systems and washing-up liquid contains powerful cleaning agents that may harm paintwork and some vinyl graphics After Cleaning After cleaning your attention should be turned to drying and lubing. A water disperser such as Tf2 - is used to help drive moisture out of components where it could sit and cause harm. These products are generally aerosols to force it into hard to reach areas. Water dispersers are not recommended as lubricant, but they can be used to protect components by wiping over the exterior surfaces. The lubricant on your chain is its only defence from the elements and helps it to run more smoothly, with no irritating squeaks! Chain lube comes in many different forms. Modern oils are synthetic and often Teflon based, they are often referred to as a dry lube as they are not sticky to the touch. This stops the chain picking up grit. It also means that the adhesion to the chain is not so good in wet conditions. Wax based lubes fall into a similar category, dry to the touch, clean but not as resistant to water wash-out. When deciding on the correct type of oil to use, a number of factors should be considered, mainly the type of bike, the time of year and the conditions in which the bike is predominantly used. For example road bikes do not require heavy oils even in the worst conditions and the cleaner wax or Teflon based formulas are sufficient all year round. A mountain biker will need to choose a different type of oil to cope with mud but will need to consider whether the oil will fling which can cause problems with modern disc brake systems. Very little oil goes a long way on a drive train as it is constantly turning and the oil will transfer to each of the components. By only applying fresh oil to a cleaned chain the life of your components can be extended General Just like your car, certain components on a bike are prone to everyday wear and tear and need to be changed frequently. Cables will need to be changed to ensure smooth operation when changing gear and braking. Brake pads and tyres will wear out and chains, no matter how well looked after, will only last so many miles. Some of this can be done at home with the right tools and know how but if you are in any doubt get your bike probably serviced by the experts. Poorly fitted components are a major cause of costly damage to your bike and put your safety at risk. An understanding of the basics of bike maintenance is an invaluable skill for any cyclist. A number of books are available that offer a great introduction to the fundamentals, combined with a quality tool kit these items will prove to be a valuable investment. |
